Skilled Training for Diploma in Electrical
►Wiring ►Motor Control ►Instrumentation ►Sub station
►Solar System ►Generator ►Automation ►Panel Design
►Microcontroller & Robotics ►Soft Skills
Wiring – 4 Classes (12 Hours)
|
Automation – 10 Classes (30 hours)
|
1. Draw the layout on the wall and set channel and cable.
|
1. Introduce to PLC.
|
2. Set switches, sockets, fan regulator, fuse, CB, MCB, MCCB.
|
2. Introduce To PLC Parameter.
|
3. Fix holder, ceiling rose, S.B and board on the wall.
|
3. Program on PLC Software.
|
4. Perform circuit operation of one lamp control for one point & two lamp control for two points.
|
4. Introduce to VFD.
|
5. Circuit operation of one lamp control for two points.
|
5. Introduce to Sensor.
|
6. Perform tube light.
|
6. Wiring & connect sensor with other accessories on PLC
|
7. Calling bell control circuit operation from two points.
|
7. Exercise (Minimum 10) program.
|
8. Connect ceiling fan.
|
8. Interfacing VFD & Sensor to PLC.
|
9. Test the polarity, continuity of wiring.
|
Panel Design – 1 Class (3Hours)
|
10. Measure the insulation resistance.
|
1. Different Size of Panel.
|
Motor Control – 6 Classes (18 Hours)
|
2. Calculation of Panel Board.
|
1. Identify NO and NC, coil terminal, auxiliary contact.
|
3. Design with AutoCAD (Electrical)
|
2. Perform timer operation.
|
Basic Electronic Circuit
|
3. Perform direct on line (DOL) connection.
|
1. Introduce to Electronics Components.
|
4. Perform star delta starter.
|
2. Measure & Test Electronics Components.
|
5. Perform R/F starter by using timer and cam starter.
|
3. PCB making & design
|
6. Perform Automatic transfer switch (ATS) connection.
|
4. Exercise (Minimum 10) projects.
|
7. Install of DB, SDB, FDB and MDB.
|
Microcontroller & robotics - 3 Classes (9 Hours)
|
8. Make fault in an industrial panel board and solve it.
|
1. Introduce to Microcontroller
|
9. Introduce phase missing relay and connect with load
|
2. PIC Based (Minimum 10) projects.
|
10. Carryout electrical connections of change over switch
|
3. Arduino Based (Minimum 10) projects.
|
11. Calculation (MC, TOR, Cable, Current)
|
4. Software Based Programming.
|
Instrumentation – 4 Classes (12 Hours)
|
5. Programming based circuit design.
|
1. Temperature Controller.
|
Solar System – 2 Classes (6 Hours)
|
2. Fuse, CB, MCB, and MCCB.
|
1. Draw the diagram of solar system
|
3. Timer.
|
2 .Explain install process
|
4. Relay.
|
3. Test performance after installation
|
5. Magnetic Contactor.
|
4. Perform maintenance of solar panel
|
6. Proximity Sensor.
|
5. Describe battery charging system
|
7. RTC, TC.
|
6. Describe charge controller
|
8. Limit Switch.
|
7. Repair and maintenance of solar equipment
|
9. Solenoid valve.
|
Generator – 1 Class (3 Hours)
|
10. Phase Failure Relay.
|
1. Describe generator
|
11. Pneumatic Valve.
|
2. Perform generator connection with load
|
12. Thermal over Load Relay.
|
3. Explain parallel operation
|
13. VFD
|
4. Explain the necessary of load sharing
|
14. Cable Connector
|
Soft Skills – 1 Class (3 Hours)
|
15. Cable Lug’s
|
1. Create CV.
|
16. Pressure Switch
|
2. Face Interview Board.
|
Substation – 4 Classes (12 Hours)
|
3. Communicate to Colleague, Boss and Subordinate.
|
1. Describe parts of sub-station
|
If necessary include short course
|
2. Single line diagram of a substation &switch gear.
|
1.
|
3. Explain the necessity of substation
|
2.
|
4. Describe isolator, Earthling and lightning arrestor
|
3.
|
5. Describe the working principle of switch gear
|
4.
|
6. Describe Protective device of switch gear
|
5.
|
7. Describe PFI
|
6.
|