Industrial
Training for Diploma in Electrical
►Wiring ►Motor Control ►Instrumentation ►Sub station
►Solar System ►Generator ►Automation ►Panel
Design
►Microcontroller & Robotics ►Soft Skills
Wiring – 4 Classes (12 Hours)
|
Automation – 10
Classes (30 hours)
|
1. Draw the layout on the
wall and set channel and cable.
|
1. Introduce to PLC.
|
2. Set switches, sockets, fan
regulator, fuse, CB, MCB, MCCB.
|
2. Introduce To PLC
Parameter.
|
3. Fix holder, ceiling rose,
S.B and board on the wall.
|
3. Program on PLC Software.
|
4. Perform circuit operation
of one lamp control for one point & two lamp control for two points.
|
4. Introduce to VFD.
|
5. Circuit operation of one
lamp control for two points.
|
5. Introduce to Sensor.
|
6. Perform tube light.
|
6. Wiring & connect
sensor with other accessories on PLC
|
7. Calling bell control
circuit operation from two points.
|
7. Exercise (Minimum 10) program.
|
8. Connect ceiling fan.
|
8. Interfacing VFD & Sensor to PLC.
|
9. Test the polarity,
continuity of wiring.
|
Panel Design – 1
Class (3Hours)
|
10. Measure the insulation
resistance.
|
1.
Different Size of Panel.
|
Motor Control – 6 Classes (18 Hours)
|
2. Calculation of Panel
Board.
|
1. Identify NO and NC, coil
terminal, auxiliary contact.
|
3. Design with AutoCAD (Electrical)
|
2. Perform timer operation.
|
Basic Electronic Circuit
|
3. Perform direct on line
(DOL) connection.
|
1. Introduce to Electronics
Components.
|
4. Perform star delta
starter.
|
2. Measure & Test Electronics Components.
|
5. Perform R/F starter by
using timer and cam starter.
|
3. PCB making & design
|
6. Perform Automatic transfer
switch (ATS) connection.
|
4. Exercise (Minimum 10)
projects.
|
7. Install of DB, SDB, FDB
and MDB.
|
Microcontroller
& robotics - 3 Classes (9 Hours)
|
8.
Make fault in an industrial panel board and solve it.
|
1. Introduce
to Microcontroller
|
9. Introduce phase missing relay and connect with
load
|
2. PIC Based (Minimum 10) projects.
|
10. Carryout electrical
connections of change over switch
|
3. Arduino Based (Minimum 10) projects.
|
11.
Calculation (MC, TOR, Cable, Current)
|
4. Software Based Programming.
|
Instrumentation – 4
Classes (12 Hours)
|
5. Programming based circuit design.
|
1.
Temperature Controller.
|
Solar System – 2 Classes
(6 Hours)
|
2.
Fuse, CB, MCB, and MCCB.
|
1.
Draw the diagram of solar system
|
3.
Timer.
|
2
.Explain install process
|
4.
Relay.
|
3.
Test performance after installation
|
5.
Magnetic Contactor.
|
4. Perform maintenance of
solar panel
|
6.
Proximity Sensor.
|
5.
Describe battery charging system
|
7.
RTC, TC.
|
6.
Describe charge controller
|
8.
Limit Switch.
|
7.
Repair and maintenance of solar equipment
|
9.
Solenoid valve.
|
Generator – 1 Class
(3 Hours)
|
10.
Phase Failure Relay.
|
1.
Describe generator
|
11.
Pneumatic Valve.
|
2.
Perform generator connection with load
|
12.
Thermal over Load Relay.
|
3.
Explain parallel operation
|
13.
VFD
|
4.
Explain the necessary of load sharing
|
14.
Cable Connector
|
Soft Skills – 1 Class
(3 Hours)
|
15.
Cable Lug’s
|
1. Create CV.
|
16.
Pressure Switch
|
2. Face Interview Board.
|
Substation – 4 Classes (12 Hours)
|
3. Communicate to Colleague, Boss and Subordinate.
|
1.
Describe parts of sub-station
|
If necessary include short
course
|
2.
Single line diagram of a substation &switch gear.
|
1.
|
3.
Explain the necessity of substation
|
2.
|
4.
Describe isolator, Earthling and lightning arrestor
|
3.
|
5.
Describe the working principle of switch gear
|
4.
|
6.
Describe Protective device of switch gear
|
5.
|
7.
Describe PFI
|
6.
|